Add nodes to cluster

New nodes that are properly configured are provisioned automatically. When you start a node with the address of at least one other running node in the wsrep_cluster_address variable, this node automatically joins and synchronizes with the cluster.

Note

Any existing data and configuration will be overwritten to match the data and configuration of the DONOR node. Do not join several nodes at the same time to avoid overhead due to large amounts of traffic when a new node joins.

Percona XtraDB Cluster uses Percona XtraBackup for State Snapshot Transfer and the wsrep_sst_method variable is always set to xtrabackup-v2.

Start the second node

Start the second node using the following command:

[root@pxc2 ~]# systemctl start mysql

After the server starts, it receives SST automatically.

To check the status of the second node, run the following:

mysql@pxc2> show status like 'wsrep%';

Expected output

+----------------------------------+--------------------------------------------------+
| Variable_name                    | Value                                            |
+----------------------------------+--------------------------------------------------+
| wsrep_local_state_uuid           | a08247c1-5807-11ea-b285-e3a50c8efb41             |
| ...                              | ...                                              |
| wsrep_local_state                | 4                                                |
| wsrep_local_state_comment        | Synced                                           |
| ...                              |                                                  |
| wsrep_cluster_size               | 2                                                |
| wsrep_cluster_status             | Primary                                          |
| wsrep_connected                  | ON                                               |
| ...                              | ...                                              |
| wsrep_provider_capabilities      | :MULTI_MASTER:CERTIFICATION: ...                 |
| wsrep_provider_name              | Galera                                           |
| wsrep_provider_vendor            | Codership Oy <info@codership.com>                |
| wsrep_provider_version           | 4.3(r752664d)                                    |
| wsrep_ready                      | ON                                               |
| ...                              | ...                                              | 
+----------------------------------+--------------------------------------------------+
75 rows in set (0.00 sec)

The output of SHOW STATUS shows that the new node has been successfully added to the cluster. The cluster size is now 2 nodes, it is the primary component, and it is fully connected and ready to receive write-set replication.

If the state of the second node is Synced as in the previous example, then the node received full SST is synchronized with the cluster, and you can proceed to add the next node.

Note

If the state of the node is Joiner, it means that SST hasn’t finished. Do not add new nodes until all others are in Synced state.

Starting the Third Node

To add the third node, start it as usual:

[root@pxc3 ~]# systemctl start mysql

To check the status of the third node, run the following:

mysql@pxc3> show status like 'wsrep%';

The output shows that the new node has been successfully added to the cluster. Cluster size is now 3 nodes, it is the primary component, and it is fully connected and ready to receive write-set replication.

Expected output

+----------------------------+--------------------------------------+
| Variable_name              | Value                                |
+----------------------------+--------------------------------------+
| wsrep_local_state_uuid     | c2883338-834d-11e2-0800-03c9c68e41ec |
| ...                        | ...                                  |
| wsrep_local_state          | 4                                    |
| wsrep_local_state_comment  | Synced                               |
| ...                        | ...                                  |
| wsrep_cluster_size         | 3                                    |
| wsrep_cluster_status       | Primary                              |
| wsrep_connected            | ON                                   |
| ...                        | ...                                  |
| wsrep_ready                | ON                                   |
+----------------------------+--------------------------------------+
40 rows in set (0.01 sec)

Next steps

When you add all nodes to the cluster, you can verify replication by running queries and manipulating data on nodes to see if these changes are synchronized across the cluster.

Get expert help

If you need assistance, visit the community forum for comprehensive and free database knowledge, or contact our Percona Database Experts for professional support and services.

Community Forum Get a Percona Expert

---

Last update: 2023-07-21